Naza mv2

videl som to niekde na youtube. nemozem to video teraz najst. hovoril ze kamarat s tym padol a tie cisla na konci pri kalibracii IMU nie su na nule (jedno ma byt okolo 1 myslim) ale maju vyssie hodnoty a treba to skalibrovat.

peterrc: ešte taká otázka, pri pripájaní do PC, stačí usb kábel (resp. kábel čo je k naze) napichnúť alebo musím aj zapojiť baterku (3S) - pohonnú? A je "niečo" pri tej naze, na čo si dávať pozor? Pred lietaním, pri nastavovaní a pod.? Nejaké "nutné" kroky a pod.? Nejaké odporúčania, na čo si dávať pozor a čo "radšej" nastaviť a pod.??

Ja by som hlavne doporucoval prestudovat navod, je tam vsetko a celkom zrozumitelne napisane. Potom, keby si predsa len niecomu nerozumel, mozes zistovat na fore co a ako, ale podla mna je zakladna vec nastudovanie navodu. Sprav si na to cas a sadni si k tomu, oplati sa to.

Preco si to nekupis radsej u nas? Za tu cenu to zozenies aj tu a mas na to zaruku.

http://elektromodely.com/modely/product_info.php?cPath=564&products_id=7565

http://www.rcsvet.sk/product/sk/F450-Naza-M-V2-GPS-podvozok-1

Vysielacku podla toho, kolko chces investovat, najlacnejsia pouzitelna je Turnigy 9X, alebo Taranis (tu by som skor doporucil, ma vela 3-polohovych prepinacov), ale v zasade akukolvek 8 a viac kanalovu, potrebujes aspon 2 3-polohove prepinace ak chces vsetko vyuzit.

Teraz som nastavoval Walkera Devo 7, tak tej sa vyhni, je to otrasna vysielacka, strasny soft ma. Ale su ine znacky ako Spectrum, Futaba, JR Propo, ale tie uz su drahsie.

Turnigy robi aj novy model
http://www.hobbyking.com/hobbyking/store/__60358__Turnigy_TGY_i10_10ch_2_4Ghz_Digital_Proportional_Radio_Control_System_with_Telemetry_Mode_1_.html

ale neviem, ake su na nu odozvy, ci je dobra. Ani nie je na sklade momentalne.

Ja som Taranis kupoval u nas tu (ale pred rokom este starsiu verziu, trochu lacnejsia bola, vysla ma na 195Eur bez prijimaca aj s postovnym kurierom):
http://www.modelarstvoimi.sk/taranis-plus-x9dx8r-pcb-balenie-v-kartone/produkt/7050/16

Tato ma vyssiu cenu, ale obsahuje uz aj prijimac.

Vačšinou sa používajú 3S alebo 4S. 3S je lahšia a so 4S ma koptera vacsiu silu.
3S- lahsia, mozes viest vacsiu kapacitu= dlhsi letovy cas
4S- tazsia, mensia kapacita, ale vacsia sila

Jaj ja som si nevsimol ze ma f450, pri custom coptere to ale takto funguje.

Ja mam motor dimenzovany na 4S a 12 palcovu vrtulu, ale pouzivam 3S kvoli letovemu casu. Tak preto som to pisal

zdravim ,vsetko uz mam poskladane ,len mam problem asi s vysielackou taranis ,naza stale ukazuje chybu ,kalibroval som uz asi 20x

je to error 29

Motors Start failure caused by TX stick(s) mid point error too big
If the TX stick(s) mid point error is too big, Motors Start will fail when you execute the Combination Stick Commands (CSC) and lead to the aircraft will not takeoff.. And the LED will blink Red four times per second continually to warn you.
TX stick(s) mid point error too big can be caused by the following reasons:
(1) There is TX stick (except the throttle stick) not at center when power on the autopilot system.
(2) The TX sticks has been trimmed, which leads to the large deviation of mid point. For example, the SUB-TRIM has been adjusted for Futaba transmitter.
(3) The TX stick(s) travel has larger asymmetry.
For the reason (1), please put all TX sticks at the mid point, and then power cycle the autopilot system to re-record the mid point. If the problem continues, that can be caused by the reason (2) or reason (3), you need to adjust the output range of your TX, and then use the Assistant Software to redo the TX calibration. Please carry out the following procedures.
(1) Connect to the Assistant software, click Basic-> R/C-> Command Sticks Calibration, and push all TX sticks throughout their complete travel range to see if any stick cannot reach its largest position.
(2) Adjust the largest travel of TX stick until the cursor on the Assistant software can reach both end positions, according to your TX manual.
(3) Power cycle the autopilot system, note that power cycle is required.
(4) Redo the TX calibration according to the Assistant software.

neviete poradit co stym?



presne mam

Taranis plus x9D
Prijímač Frsky D8R-II plus ACCST Telemetria D 8-ka

zapojenie
naza
A
do
prijimac 1

postupne az na U - 5

jedine co ide je test motorov

mam nastaveny tradition iny nefunguje