Turnigy 9x a DJT combo pack

Ahojte vsetci nedavno som kupil vysielacku Turnigy 9x a dnes mi prislo domov aj FrSky DJT combo pack vsetko som zapojil tak ako to ma byt lenze nejde mi to nabindovat riadil som sa presne podla navodu pozeral videa na youtube zhanal na googli ale nikde nic som nenasiel.Problem je v tom ked na module stisnem gombik a zacne blikat led na zeleno a pipat vtedy by som mal stisnut tlacitko na prijimaci F/S a zasunut dovnutra konektor od regulatoru spolu s baterkou a prijimac by mal zacat blikat tiez,lenze nic sa nedeje viete mi niekto poradit?Diky

no tak nejak to zacalo fungovat teraz na prijimaci blika cervena led a co teraz ked pripajam servo tak ked sa dotkne kontaktov prijimaca tak ho trocku otoci ale neda sa ovladat.Prosim poradte co dalej.Dakujem.

no tak podla navodu pise ze zapnut vysielacku a podrzat F/S na module on zacne blikat a pipat vtedy mam zapnut prijimac on zacne blikat a ked sa to sparuje mal by prestat blikat a pipat modul aj prijimac a ked to tak robim tak prestane blikat len prijimac a iba svieti cervena dioda a modul robi dalej to co robil a pripojene servo nereaguje

No pokial som to precital spravne tak ak mas obojsmerny vysielac /telemetria/ mas mat prepinace na volbu telemetrie na off, potom stlacis na vysielaci F/S tlacitko a zapnes vysielac, mal by zacat blikat na cerveno a zelena sa vypne, je pripraveny na bindovanie.
na prijimaci stlacis F/S a zapnes ho , ked zacne blikat cervena led malo by to byt nabindovane.
obidva vypnut a zapnut, na vysielaci a aj na prijimaci by mala svietit cervena dioda, a zelena blikat - prijima data.

tu je to v originale.

6.2
Binding the Receiver and Transmitter
Binding is the process of uniquely associating a particular receiver and transmitter, to exclude any potentially interfering transmitters. A transmitter can be bound to multiple receivers (not to be used simultaneously). A receiver can only be bound to one transmitter. This association is a key component in newer 2.4 GHz radio systems and must be done before the equipment can be used.
6.2.1
Turn your transmitter on while holding the F/S button on the transmitter module (For the two-way mode, make sure that both switches on the transmitter module are OFF). Release the button. The RED LED on the transmitter module will flash, indicating the transmitter is ready to bind the receiver. The GREEN LED will be off.
6.2.2
Turn on the receiver while holding the F/S button. The RED LED on the receiver will flash, indicating the binding process is completed.
6.2.3
Turn off both the receiver and transmitter
6.2.4
Turn on the transmitter and the receiver. The RED LED on the receiver will be on and the GREEN LED on the receiver will continually flash as the commands from the transmitter are received.
6.2.5
After the steps above are completed, both the transmitter and receiver are ready to be used.

drzim palce.

aaa frsky, nevismol som si, pardon...

ved tak to robim akurat ono to robi vsetko naopak ked parujem tak na prijimaci svieti cerve nie blika a na vysielaci ten modul blika pipa na zeleno nie na cerverno a ked vsetko vypnem a znovu zapnem tak na prijimaci cervena dioda blika ja uz fakt neviem

no pokial drzim to tlacitko na prijimaci a zaroven dam do neho bateriu cervene tlacitko len svieti ale ak to tlacitko nestisnem tak dioda blika

prosim poradte mi este nieco lebo to skusam stale rovnako dookola a nic pritom viem ze vsetko co zapajam je 100% funkcne

Uz to mam a nebola chyba v postupnosti ale na zadnej strane su 2 prepinace nikde nebolo napisane ze ten 2. treba dat do pozicie ON vtedy som to cele zopakoval a bolo to takze to uz cele funguje

no navod som cital stale dookola v ANG aj v CZ na nete som nasiel jednu stranku a tam opisovali chybu ktoru som mal ja hovorili ze to nefunguje presne a ze to blika naopak ako to ma mna to stale miatlo no zistil som ze som to nabindoval uz na 1. krat akurat tie prepinace a diody ktore blikali inac ako mali ma miatli no ale hlavne ze ide.Ale niekto hore mi asi nedovoli lietat nakolko mi dnes buchla baterka tak musim cakat az mi z reklamacie poslu novu lebo bol to vadny kus

ano presne na tej stranke som to cital